CINCH NucWik

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== 16. Production of radionuclides ======


Chapter 16 from BASICS OF NUCLEAR PHYSICS AND OF RADIATION DETECTION AND MEASUREMENT - An open-access textbook for nuclear and radiochemistry students by Jukka Lehto

###
This chapter deals with production of radionuclides for utilization in research, medical use and industrial use etc. Production of radionuclides, such as transactinides, for the study of their properties is not discussed here. Radionuclides are produced either in [[#16.2._production_of_radionuclides_in_reactors|reactors]] or in particles accelerators, particularly [[#16.1._production_of_radionuclides_in_cyclotrons|cyclotrons]]. These two methods are complementary to each other both offering advantages over the other.
###
{{anchor:radionuclide_production_accelerators}}
{{anchor:cyclotrons}}
===== 16.1. Production of radionuclides in cyclotrons =====

###
In cyclotrons [[textbook:nrctextbook:chapter15|nuclear reactions]] are induced by bombarding [[textbook:nrctextbook:chapter15#target_nucleus|target atoms]] by proton-bearing particles, such as [[textbook:nrctextbook:chapter2#proton|protons]], [[textbook:nrctextbook:chapter2#deuterium|deuterons]] and [[textbook:nrctextbook:chapter5#alpha_particle|alpha particles]]. Depending on the [[textbook:nrctextbook:chapter15#projectile_particle|bombarding particle]] and its energy various product nuclides are obtained (see Figure XVI.3). Most reactions result in change of the [[textbook:nrctextbook:chapter2#atomic_number|atomic number]] yielding product [[textbook:nrctextbook:chapter2#nucleus|nuclei]] having a higher atomic number (or sometimes lower, for example in (d,α) reaction). These nuclei are [[textbook:nrctextbook:chapter3#neutron_to_proton_ration|proton-rich]] and therefore decay by [[textbook:nrctextbook:chapter5#positron_decay|positron emission]] or [[textbook:nrctextbook:chapter5#electron_capture|electron capture]]. Since the product nuclei are of a different element than the target nuclei cyclotrons can produce carrier-free radionuclides. This means that after chemical or physical separation the product nuclide does not contain any (or contains only very minor amounts) of stable [[textbook:nrctextbook:chapter2#isotope|isotopes]] of the same element. This results in the formation of product nuclides with very high [[textbook:nrctextbook:chapter6#specific_activity|specific activity]] (= activity divided by the mass of the product element). Use of carrier-free [[textbook:nrctextbook:chapter4|radionuclides]] is in many cases advantageous, for example in labelling of organic molecules, where as many positions in the molecules are aimed to label with a radionuclide and not with a stable isotope of the same element. In carrier-bearing radionuclide products the stable isotopes always “dilute” radionuclides and yield in lower specific activities. An example of cyclotron-produced radionuclides is <sup>22</sup>Na which can be produced from magnesium with the reaction ${}^{24}_{12}\mathrm{Mg}(d,\alpha){}^{22}_{11}\mathrm{Na}$ (t½ = 2.6 a). Since the target is made of magnesium it does not, after chemical separation of sodium from magnesium, dilute the product.
###

###
Even high [[textbook:nrctextbook:chapter6#activity|activities]] represent very low chemical amounts, for example 1 MBq of <sup>22</sup>Na corresponds to only 2×10<sup>-10</sup> moles or 4.5 ng of sodium which means that the [[textbook:nrctextbook:chapter6#specific_activity|specific activity]] is very high at 5×10<sup>15</sup> Bq/mol or 2×10<sup>14</sup> Bq/g. In practice completely carrier-free radionuclides are not achieved due to contamination. Furthermore, small amounts of carrier are often added to the system to prevent losses of the radionuclides due to adsorption, for example.
###
{{anchor:radionuclide_production_reactors}}
===== 16.2. Production of radionuclides in reactors =====
###
As [[textbook:nrctextbook:chapter16#cyclotrons|cyclotrons]] produce [[textbook:nrctextbook:chapter3#neutron_to_proton_ration|proton-rich]] [[textbook:nrctextbook:chapter4|radionuclides]] reactors produce [[textbook:nrctextbook:chapter3#neutron_to_proton_ration|neutron-rich]] ones. The reactions needed for radionuclide reactions are typically [[textbook:nrctextbook:chapter15#neutron_capture|neutron capture]] reactions by using [[textbook:nrctextbook:chapter15#thermal_neutron|thermal neutrons]]. An example of such reactions is ${}^{23}_{11}\mathrm{Na}(n,\gamma){}^{24}_{11}\mathrm{Na}$ to produce <sup>24</sup>Na (t½ = 15 h). As is seen from the reaction formula both the [[textbook:nrctextbook:chapter15#target_nucleus|target]] and the product are of same element, sodium in this case. Thus all radionuclides produced in reactors using ($n, \gamma$) neutron capture reaction results in the formation of products containing carrier and therefore the [[textbook:nrctextbook:chapter6#specific_activity|specific activities]] of such radionuclides are fairly low. <sup>24</sup>Na produced by neutron capture reactions has a specific activity of 1011 Bq/g Na at maximum, whereas <sup>24</sup>Na produced from <sup>26</sup>Mg in cyclotron by the ($d, \alpha$) yields a high specific activity of 10<sup>13</sup> Bq/g Na. The neutron-rich radionuclide produced in reactors decay by [[textbook:nrctextbook:chapter5#beta|beta decay]] (β<sup>-</sup>) to elements having a higher [[textbook:nrctextbook:chapter2#atomic_number|atomic number]]. In the case the desired radionuclide is a radionuclide produced in the β<sup>-</sup> decay of the primary product produced in a [[textbook:nrctextbook:chapter15#neutron_capture|neutron capture]] reactions. Carrier-free radionuclides can be obtained after chemical separation. Radionuclides can be produced by reactors also by utilizing fission reactions, particularly [[textbook:nrctextbook:chapter15#thermal_neutron|thermal neutron]] [[textbook:nrctextbook:chapter15#induced_fission|induced fission]] of <sup>235</sup>U. In this case the number of radionuclides produced is high and the required separations for desired radionuclide/s may be laborious and time-consuming.
###

###
[[textbook:nrctextbook:chapter15|Chapter XV]] describing nuclear reactions give the equations ([[textbook:nrctextbook:chapter15#nuclear_reaction_kinetics|XV.XI-XV.XVI]]) and [[textbook:nrctextbook:chapter15#figure_152|Figure XV.2]] presenting the [[textbook:nrctextbook:chapter15#nuclear_reaction_kinetics|kinetics of nuclear reactions]] used in [[textbook:nrctextbook:chapter4|radionuclide]] productions. These equations are needed to calculate the required irradiation times to produce a radionuclide with known [[textbook:nrctextbook:chapter6#half_life|half-life]] using a [[textbook:nrctextbook:chapter15|nuclear reaction]] with known [[textbook:nrctextbook:chapter15#cross_section|cross section]] at given irradiation flux and bombarding energy.
###
{{anchor:radiochemical_purity}}
{{anchor:tracers}}
===== 16.3. Radiochemical and radionuclidic purity =====

###
When a tracer experiment with a certain [[textbook:nrctextbook:chapter4|radionuclide]] is done it is most often desirable that there are not any other radionuclides present since measurement of single radionuclide is easier as no radiochemical separations nor spectrometric analysis are needed. When a tracer product contains only one specific radionuclide, it is called radionuclidic pure. Radionuclide purity as a measure means the activity fraction of a specific radionuclide of the total activity. To produce radionuclidic pure tracers by [[textbook:nrctextbook:chapter15|nuclear reactions]] is not an easy task. The conditions in production reactions, particularly [[textbook:nrctextbook:chapter15#projectile_particle|projectile]] energy and bombardment time, should be kept so that only one product nuclide is observed. This is, however, not typically possible since the [[textbook:nrctextbook:chapter15#cross_section|cross sections]] of various reactions overlap in [[textbook:nrctextbook:chapter15#excitation_function|excitation function]]. For example, if <sup>209</sup>Po tracer is produced in [[textbook:nrctextbook:chapter16#cyclotrons|cyclotron]] by bombarding <sup>209</sup>Bi with [[textbook:nrctextbook:chapter2#deuterium|deuterons]] by the reaction ${}^{209}\mathrm{Bi}(d, 2n){}^{209}\mathrm{Po}$ the optimum deuteron energy of about 15 MeV, resulting in the highest yield, may not be used due to coproduction of <sup>208</sup>Po. Instead, somewhat lower deuteron energies should be applied to minimize the fraction of <sup>208</sup>Po (Fig. XVII.1).
###

{{:textbook:nrctextbook:excitation_function_of_209bi_ractions_fig_16_1.png|}}
Figure XVI.1. Excitation function of <sup>209</sup>Bi(α,xn)-reactions (data from Ramler et al. Physical Review 114(1959)154).

###
Another critical factor in producing //radionuclidic pure// tracers is the purity of the [[textbook:nrctextbook:chapter15#target_nucleus|target material]]. Even very low amounts of impurities may result in considerable amounts of undesired [[textbook:nrctextbook:chapter4|radionuclides]] in the product, especially in case where the impurity atoms have higher [[textbook:nrctextbook:chapter15#cross_section|cross sections]] for the used [[textbook:nrctextbook:chapter15#projectile_particle|projectiles]] than the actual target atoms. To avoid formation of undesired radionuclides elementally very pure targets are typically needed. In some cases, elementally pure targets are not enough to prevent formation of undesired radionuclides, but even isotopically pure targets are needed. For example, in the production of <sup>18</sup>F by the reaction ${}^{18}\mathrm{O}(p,n){}^{18}\mathrm{F}$ water enriched with respect to <sup>18</sup>O is used as the target. The enrichment of <sup>18</sup>O in the target water is about 97% while in the natural water it is only 0.2%. Isotopically pure target materials may be very expensive.
###

###
In addition to radionuclidic purity another term, //radiochemical purity// is important, particularly in labelling of organic molecules, for radiopharmaceutical purpose for example. Radiochemically pure compounds are the desired compounds containing the radionuclide or the compounds containing the radionuclide in a desired position. In, for example, <sup>18</sup>F-labelled radiopharmaceutical 2-FDG (2-deoxy-2-[<sup>18</sup>F]fluoro-D-glucose) product the radiochemically impure compounds are those where the <sup>18</sup>F-label is somewhere else than in 2-deoxy position or other <sup>18</sup>F-labelled compounds, such as tetra-acetyl-2-[<sup>18</sup>F]FDG.
###
{{anchor:radionuclide_generators}}
===== 16.4. Radionuclide generators =====

###
Radionuclide tracers are commercially typically available as liquids containing radionuclides as ions, for example <sup>137</sup>CsCl and NH<sub>4</sub>H<sup>32</sup>PO<sub>4</sub> or as labelled compounds, such as [methyl-
<sup>14</sup>C]methionine and [<sup>35</sup>S]methionine. A number of radionuclide tracers are available in a mode of generator. In these a radionuclide, produced either in a [[textbook:nrctextbook:chapter16#radionuclide_production_reactors|reactor]] or a [[textbook:nrctextbook:chapter16#cyclotrons|cyclotron]], is trapped in column containing a sorbent, such as alumina, capable of sorbing this radionuclide. In the column the sorbed radionuclide decays to its daughter nuclide which is the desired tracer nuclide. The sorbent needs to efficiently trap the parent nuclide but not the daughter which should be eluteable out from the column while the parent nuclide remains. Another requirement is that the [[textbook:nrctextbook:chapter6#half_life|half-life]] of the daughter is shorter than that of the parent; otherwise no radiochemical [[textbook:nrctextbook:chapter6#activity_equilibrium|equilibrium]] would be attained in the column.
###

###
As examples of radionuclide generators, the <sup>99m</sup>Tc and <sup>137m</sup>Ba generators are described. In a Tc generator the parent <sup>99</sup>Mo (t½ = 66 h), produced in a [[textbook:nrctextbook:chapter16#radionuclide_production_reactors|reactor]] by [[textbook:nrctextbook:chapter15#neutron_capture|neutron activation]] of stable <sup>98</sup>Mo, is trapped in an aluminum oxide column where it [[textbook:nrctextbook:chapter5|decays]] to a short-lived <sup>99m</sup>Tc (t½ = 6.0 h). Tc forms an anionic TcO<sub>4</sub><sup>-</sup> ion that can be eluted from the column with NaCl solution while <sup>99</sup>Mo remains in the column as MoO<sub>4</sub><sup>2-</sup>. <sup>99m</sup>Tc is widely used as a radiopharmaceutical in hospitals in single photon tomography imaging of humans. <sup>99m</sup>Tc emits fairly energetic [[textbook:nrctextbook:chapter5#gamma|gamma rays]] (143 keV) which can be readily detected with [[textbook:nrctextbook:chapter9|gamma detectors]].
###

###
In a <sup>137m</sup>Ba (t½ = 2.6 min) generator the parent <sup>137</sup>Cs (t½ = 30 y) is trapped in transition metal hexacyanoferrate column, such as K<sub>2</sub>CoFe(CN)<sub>6</sub>. In the column the parent decays to <sup>137m</sup>Ba which can be eluted from the column with NaCl solution. Transition metal hexacyanoferrates are extremely selective for cesium and thus trap it very efficiently. <sup>137m</sup>Ba is used in monitoring of industrial processes for example in examining flow profiles on liquids in pipes. <sup>137m</sup>Ba emits energetic gamma rays (662 keV) which can be detected from outer surfaces of pipes, for example.
###

Table XVI.I Most important radionuclide generators.

^Mother nuclide^Decay properties^Daughter nuclide^Decay properties^Application^
|<sup>41</sup>Ti |EC, γ; 47 y |<sup>44</sup>Sc |β<sup>+</sup>, γ; 3.9 h |Teaching|
|<sup>68</sup>Ge |EC; 288 d |<sup>68</sup>Ga |β<sup>+</sup>, γ; 1.1 h |Medical|
|<sup>87</sup>Y |EC, 3.3 d |<sup>87m</sup>Sr |γ; 2.8 h |Medical & teaching|
|<sup>90</sup>Sr |β<sup>-</sup>; 28 y |<sup>90</sup>Y |β<sup>-</sup>; 64 h |Heat/calibration source| 
|<sup>99</sup>Mo |β<sup>-</sup>; 66 h |<sup>99m</sup>Tc |γ; 6.0 h |Medical|
|<sup>113</sup>Sn |EC, γ; 115 d |<sup>113m</sup>In |γ; 1.7 h |Medical|
|<sup>132</sup>Te |β<sup>-</sup>, γ; 76 h |<sup>132</sup>I |β<sup>-</sup>, γ; 2.3 h |Medical|
|<sup>137</sup>Cs |β<sup>-</sup>, γ; 30 y |<sup>137m</sup>Ba |γ; 2.6 m |Gamma radiography & Radiation sterilization| 
|<sup>140</sup>Ba |β<sup>-</sup>, γ; 13 d |<sup>140</sup>La |β<sup>-</sup>, γ; 40 h |Lanthanum tracer| 
|<sup>144</sup>Ce |β<sup>-</sup>, γ; 284 d |<sup>144</sup>Pr |β<sup>-</sup>; 17 m |Calibration source| 
|<sup>210</sup>Pb |β<sup>-</sup>, γ; 21 y |<sup>210</sup>Bi |β<sup>-</sup>; 5.0 d |Calibration source| 
|<sup>226</sup>Ra |α, 1600 y |<sup>222</sup>Rn |α, 3.8 d |Medical|
|<sup>238</sup>U |α, 4.5 Gy |<sup>234</sup>Th |β<sup>-</sup>, γ; 24 d |Thorium tracer|
CINCH NucWik

Sidebar

A-CINCH Consortium

CINCH NucWik

User Tools

Site Tools

Sidebar

Page Tools

A-CINCH Consortium
